parameters to measure when using the boiler for superheated steam

parameters to measure when using the boiler for superheated steam

ZOZEN has built six fully automatic lines for the production of convection pipe, coil pipe, threaded pipe, membrane wall, serpentine tube and header. The parts so produced have consistent dimensions that enable easy assembly and ten years’ extension of a boiler’s life.


1. Convection pipe production line: high precision of ±0.5MM.
2. Coil pipe production line: three pieces of pipes can be coiled at the same time. 114mm diameter pipes are coiled into 4.5 meters coil.
3. Threaded smoke pipe production line: tread depth is accurately measured by infrared radiation to ensure tread depth is proper.
4. Membrane wall production line: MPM automatic welding machine with 12 heads, 1600MM panel bending machine.
5. Serpentine tube production line: 150 meters pipe can be made into economizer or super heater in one time without manual seam.
6. Header production line: by medium frequency electric heating, mechanical flow forming closing and NC drilling.

Our Lastest Boiler Type

Seven Hold Points

Seven hold points are set and each one is supervised by a responsible inspector. Any work that fails to pass the inspection cannot proceed until the inspector is able to verify its quality.

1,Incoming materials are inspected again upon entry into the plant.

2,Material markings will be transferred to all cut pieces to ensure identification and traceability.

3,Test pieces are used to ensure a higher success rate in welding.

Unique structural design

National Precision Bearing offers stainless steel for applications that require corrosion resistance.We have world class manufacuring facilities using latest technology, machines and equipments.

Contact Us

No OSHA Compliance - TV Trop

;The movie ends in a stock movie location I thought had been retired: a steam and flame factory where the combatants stalk each other on catwalks and from behind steel pillars, while the otherwise deserted factory supplies vast quantities of flame and steam.;

Contact us

Combustion Fundamentals - Industrial Wiki - odesi

Combustion Principles. Combustion is the rapid oxidation of material (the fuel) to release energy ().The fuel can be a solid, liquid or gas, and the amount of heat released is normally expressed in BTUs (British thermal units) or Calories.

Contact us

What is the difference between pinch point an

Pinch point is the temperature difference between the gas turbine exhaust leaving the evaporator section and the saturation temperature of steam at

Contact us

MANITOWOC CONVOTHERM 4 INSTALLATIO

View and Download Manitowoc Convotherm 4 installation manual online. combi steamer. Convotherm 4 Kitchen Appliances pdf manual download.

Contact us

Initial Plant Assessment Report - RATCH - Austral

5 | P a g e production and fuel consumption figures given in Table 1. Both these configurations include the fossil fuelled boiler and are based on same overall sized solar field.

Contact us

Hydroprocessing - EP

Date : Replies: 22/11/2018 Q: Can anyone explain me what are all the parameters that affect H2 purity in Recycle gas in case of a Hydrotreater/Hydrocracker ?

Contact us

AEP’s John W. Turk, Jr. Power Plant Earns POWER’

First USC Boiler in the U.S. The Turk Plant was the natural evolution of AEP’s early use of supercritical boiler technology which began with the Philo Unit 6 in Ohio (the world’s first

Contact us

Aseptic Processing and Packaging for the Food Indust

Updated: . GUIDE 1 TO INSPECTIONS OF ASPECTIC PROCESSING AND PACKAGING FOR THE FOOD INDUSTRY. 1 This document is reference materials for investigators and other FDA personnel. The

Contact us

No OSHA Compliance - TV Trop

;The movie ends in a stock movie location I thought had been retired: a steam and flame factory where the combatants stalk each other on catwalks and from behind steel pillars, while the otherwise deserted factory supplies vast quantities of flame and steam.;

Contact us

Initial Plant Assessment Report - RATCH - Austral

5 | P a g e production and fuel consumption figures given in Table 1. Both these configurations include the fossil fuelled boiler and are based on same overall sized solar field.

Contact us

What is the difference between pinch point an

Pinch point is the temperature difference between the gas turbine exhaust leaving the evaporator section and the saturation temperature of steam at

Contact us

Chapter 78 - Oil and Natural Gas - iloc

Basic refining processes and operations. Petroleum refining processes and operations can be classified into the following basic areas: separation, conversion, treatment, formulating and blending, auxiliary refining operations and refining non-process operations.

Contact us

ASME.PTC4.1 .Boiler efficiency test | Boiler | Ste

1. ENERGY PERFORMANCE ASSESSMENT OF BOILERS 1.1 Introduction Performance of the boiler, like efficiency and evaporation ratio reduces with time, due to poor combustion, heat transfer fouling and poor operation and maintenance.

Contact us

Combustion Fundamentals - Industrial Wiki - odesi

Combustion Principles. Combustion is the rapid oxidation of material (the fuel) to release energy ().The fuel can be a solid, liquid or gas, and the amount of heat released is normally expressed in BTUs (British thermal units) or Calories.

Contact us

Exhaust Gas Boilers And Economisers workin

Exhaust Gas Boilers And Economisers Arrangement Auxiliary boilers on diesel main propulsion ships, other than tankers, are usually of composite form, enabling steam generation using oil firing or the exhaust gases from the diesel engine.

Contact us

Martindale's Calculators On-Line Center: Mechanica

spring ; spring design. compression spring calculators, applets, etc. extension spring calculators, applets, etc. torsion spring calculators, applets, etc.

Contact us

Hydroprocessing - EP

Date : Replies: 22/11/2018 Q: Can anyone explain me what are all the parameters that affect H2 purity in Recycle gas in case of a Hydrotreater/Hydrocracker ?

Contact us

Aseptic Processing and Packaging for the Food Indust

Updated: . GUIDE 1 TO INSPECTIONS OF ASPECTIC PROCESSING AND PACKAGING FOR THE FOOD INDUSTRY. 1 This document is reference materials for investigators and other FDA personnel. The

Contact us

Martindale's Calculators On-Line Center: Mechanica

spring ; spring design. compression spring calculators, applets, etc. extension spring calculators, applets, etc. torsion spring calculators, applets, etc.

Contact us

Pages - Pressurised Deaerato

Pressurised Deaerators Why gases need to be removed from boiler feedwater. Oxygen is the main cause of corrosion in hotwell tanks, feedlines, feedpumps and boilers.

Contact us

PROPERTIES OF STEAM AND WATER

PROPERTIES OF STEAM AND WATER. INTRODUCTION . The process by which we convert water into steam and use the steam to turn a propulsion shaft encompasses the generation and expansion phases of the steam cycle.

Contact us